DRILL BIT SHARPENER MACHINE -DM TYPE
DRILL BIT SHARPENER MACHINE -DM TYPE
- Loosen the side knob (B1) and open the side cover (B2).
- Use a 4mm hexagon wrench to loosen the screw (B3), unscrew it counter clockwise.
- Replace with a new diamond grinding wheel and tighten the screw after the wheel is installed.
- Be sure to close the side cover (B2) properly and to fasten the side knob (B1).
Please DO NOT switch on the machine BEFORE
- The diamond wheel screw (B3) is tightly screwed.
- The side cover (B2) is properly closed.
- The right knob (B1) is fully fastened.
※ In case of any hazard occurring, please make sure that the above measures are followed strictly.
※ The machine has an automatic Power-off device to ensure operator’s safety. Power supply will be cut-off immediately when the cover is opened.
| Type | DM-213 | DM-320 | DM-1226 |
| Standard Accessories | ER20 collet 2.5mm-13mm(12 pcs) | ER25 collet 3mm-20mm(18 pcs) | ER40 collet 12mm-26mm(15 pcs) |
| CBN#200 Diamond Wheel*1 (For HSS) | CBN#200 Diamond Wheel*1 (For HSS) | CBN#150 Diamond Wheel*1 (For HSS) | |
| 4mm、5mm Hexagon wrench 1 pcs each | 4mm、6mm wrench 1 pcs each | 4mm、6mm wrench 1 pcs each |
| Type | DM-213 | DM-320 | DM-1226 |
| Optional Accessoreis | CBN#200 Diamond Wheel | SDC#200 Diamond Wheel | SDC#200 Diamond Wheel |
| SDC#200、SDC#400 Diamond Wheel | - | - | |
| ER20 collet 2.5mm-13mm(12 pcs) | - | ER40 collet 8mm-11mm、27mm-30mm(8 pcs) |
| Type | DM-213 | DM-320 | DM-1226 |
|---|---|---|---|
| Drill Diameter | 2mm – 13mm | 3mm – 20mm | 12mm – 26mm |
| Point Angle | 85° ~ 140° | 85° ~ 140° | 85° ~ 140° |
| Power | AC 110 / 50HZ AC 220 / 60HZ | AC 110 / 50HZ AC 220 / 60HZ | AC 110 / 50HZ AC 220 / 60HZ |
| Motor | 150 W | 450W | 450W |
| R.P.M | 4600 RPM | 4300 RPM | 3700 RPM |
| Weight | 10.5 kgs | 21 kgs | 29 kgs |
| Dimensions | 305 x 172 x 180 mm | 480 x 260 x 240 mm | 470 x 260 x 235 mm |
Safety Instructions
Names of Components
Preparation Before Grinding Drill
Drill Grinding procedures
Replacing The Grinding Wheel
Maintenance After Operation
Recommend
ENDMILL HELIX RE-SHARPENING EH TYPE
ENDMILL HELIX RE-SHARPENING EH TYPE
- The universal tool & cutter grinder Model EH-832 is versatile in operation without requiring special skills. All milling cutters, endmills, shell endmills,staggered tooth cutters, rough endmills, countersinks (2 flutes, 4 flutes) and the angle of endmill helix can sharpen 2, 3, 4, 5, 6 flutes.
- The Model EH-832 is designed to sharpen HSS and carbide toolings in small and medium quantities.
- In one chucking operation, the machine can perform the grinding of the rake angle of the flute, clearance angle on the periphery and the end of the tool.
- A few seconds set up time for helix angle.
- Due to the backlash free operation, spiral toothed, solid carbide or carbide tipped milling cutters can be ground with high accuracy thus far only achieved by CNC grinders.
- The heavy duty compound slides and one piece cast-iron base provide extra rigidity and minimize vibration.
DRILL BIT SHARPENER MACHINE -SG TYPE
DRILL BIT SHARPENER MACHINE -SG TYPE
1.Drill tightened design with bearing device.
2.Adjustable trimmimg angle.
3.Adjustable secondary clearance angle.
Patent number:
ZL 200820153366.2,
Japan 3151952,
M 356596,
Nr 202008013817.5